Redcat Racing Tenergy-90263 All-In-One LI-PO Battery Charger
Redcat Racing Tenergy-90263 LI-PO Battery Charger & Power Supply
The best ALL-IN-ONE Universal Charger on the market!
Various Connectors Supported:
- Hitech
- JST
- Deans
- Tamiya
- Traxxas
No extra hassle of trying to find connector adapters, or worrying about if your Hobby battery pack is supported.
Supports multiple types of battery packs with one single charger! The follow packs are supported:
- NiMH/NiCD 1~15 cells ( 1.2v to 18v)
- Li-PO/Lithium Ion 1~6 series ( 3.7v to 22.2v)
- Li-Fe 1~6 series
- Sealed Lead Acid (SLA)
Charger Specifications:
- Handle NiMH, NICD, Li-Po,Li-ion, Li-Fe, SLA Batteries
- Build-in Balance
- Temperature Sensor
- DC 11V~15V, which can be directly connect to Automobile Battery. The working electric current is less than 5A when it is charged in full load. The current of the fuse is 10A which could prevent short circuit.
Specification | |
Operating voltage | DC 11~18 volts AC 100~240V, 50/60Hz |
Charge/discharge power | max. 50/5 Watts |
NiCd/MH | 1~15 cells |
LiIo/LiPo/LiFe | 1~6 series |
Pb | 2~20V |
Charge current | 0.1 to 5.0A |
Discharg current | 0.1 to 1.0A |
No. of cycle | 1 to 5 times |
Battery data memory | up to 5 data |
Weight | 1000g |
Dimension | 160x120x40 mm |
User’s setting-up parameters | |
Battery voltage type | LiIo:3.6V, LiPo:3.7V, LiFe:3.3V |
NiCd Delta-peak voltage sensitivity | 1 to 20mV |
NiMH Delta-peak voltage sensitivity | 1 to 20mV |
Battery temperature cut-off | 20 to 80C or OFF |
Waiting time between charge/discharge | 1 to 60 min. |
Integral timer limit for safety | 10 to 720 min.or OFF |
Maximum charging capacity limit for safety | 10 to 9990mAh or OFF |
Key beep and buzzer sound | ON/OFF |
Input DC power low alert | 10 to 11V |
Warning
- Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode if mishandled.
- NOTE: Please do NOT charge 2 NIMH packs in serial or parallel
- Protective Circuit Board is required when making packs
- Make sure user has enough knowledge on Li-Ion rechargeable batteries in charging, discharging and assembly before use.
- Put the batteries in fire-proof container in charging
- Never leave batteries unattended when charging
- Do not put batteries on wood surface or carpet when charging
- We are not responsible for any damage caused by misuse or mishandling of Li-Ion batteries in charging
- We are not responsible for damage caused by other Li-ion batteries not supplied from us
- Do not make any changes to the charger, charger accessories or connectors, as this might cause electrical shortage, fire or over-heating during charging. We are not liable for the product is any changes are made to the charged accessories or connectors.
Constant Current Switch Power Supply
- Input: 100-240V AC, 50/60Hz 2A
- Output: 12V, 5A
- Perfect for Micro-control LCD Li-Po Ballance Charger
Warning
- Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode if mishandled.
- NOTE: Please do NOT charge 2 NIMH packs in serial or parallel
- Protective Circuit Board is required when making packs
- Make sure user has enough knowledge on Li-Ion rechargeable batteries in charging, discharging and assembly before use.
- Put the batteries in fire-proof container in charging
- Never leave batteries unattended when charging
- Do not put batteries on wood surface or carpet when charging
- We are not responsible for any damage caused by misuse or mishandling of Li-Ion batteries in charging
- We are not responsible for damage caused by other Li-ion batteries not supplied from us
- Do not make any changes to the charger, charger accessories or connectors, as this might cause electrical shortage, fire or over-heating during charging. We are not liable for the product is any changes are made to the charged accessories or connectors.
Fill out my online form.
There are no comments yet, add one below.